ALDEX C-800 Series Resins

C-800H Strong Acid Cation Exchange Resin

Tested and certified by WQA according to NSF/ANSI/CAN 61 and 372, NSF/ANSI 44 and CSA B483.1. Aldex C-800H is a strongly acidic, high-quality, gel-type cation resin supplied in the hydrogen form. It is manufactured under special conditions to meet the exacting requirements for ultrapure water production.

 

Aldex C-800H Technical Bulletin: English (PDF)  |  Français (PDF)

Aldex C-800 H Safety Data Sheets: English (PDF) | Français (PDF)

 

Physical Chemical Properties

Polymer Structure: Sulfonated styrene/divinylbenzene copolymer
Ionic Form as Shipped:Hydrogen
Physical Form: Tough, spherical, black beads
Screen Size Distribution:

-16+40 mesh (U.S. Std.)
-40+50 mesh


99%
1% maximum
pH Range:0 to 14
Moisture Content:50 to 56%
Conversion to H+ Form:99% minimum
Shipping Weight: 50 lbs per cubic foot
Total Capacity H+Form:
1.8 meq/ml minimum
Specific Gravity:1.23

Recommended Operating Conditions

Influent pH:No restrictions
Maximum Temperature:250 °F
Bed Depth:Minimum 24”
Normal 36”
Service Flow Rate:1 to 10 US GPM per cubic foot
Backwash Flow Rate:See Fig. 1
Regenerant:1 to 8% H2SO4 or HCl
Regenerant Flow Rate:0.3 to 1.5 US GPM per cubic foot of resin
Regenerant Contact Time:15 to 60 minutes
Regenerant Dosage Level: 2 to 15 lb of regenerant per cubic foot
Slow Rinse (Displacement) Flow Rate:0.3 to 1.5 US GPM per cubic foot
Slow Rinse Volume:20 USG per cubic foot resin
Fast Rinse Rate:1.0 to 10 US GPM per cubic foot
Fast Rinse Volume:30 to 60 USG per cubic foot resin

C-800H Features

Elemental analysis, dry basis

Sodium (Na)<100 ppm
Cobalt (Co)<50 ppm
Copper (Cu)<50 ppm
Aluminum (Al) <50 ppm
Iron (Fe) <50 ppm

Very Low TOC

Non-solvent sulfonation and special manufacturing processes assure very low TOC leakage.

Uniform Particle Size

99% of all beads are in the minus 16 to plus 40 mesh range: giving a lower pressure drop while maintaining the superior kinetics of standard mesh size products.

Superior Physical Stability

90% plus sphericity and high crush strengths together with a very uniform particle size provide greater resistance to bead breakages and maintain low-pressure drops.

Safety Information

A material safety data sheet is available for Aldex C-800H. Copies can be obtained from Aldex Chemical Co., LTD. Aldex C-800H is not a hazardous product and is not WHMIS-controlled.

Caution: Acidic and basic regenerant solutions are corrosive and should be handled in a manner that will prevent eye and skin contact. Before using strong oxidizing agents in contact with ion exchange resin, consult sources knowledgeable in the handling of these materials.

 

Backwash Characteristics

Aldex C-800H should be backwashed for at least 10 minutes after each service cycle in a conventional downflow regenerate unit. To reclassify the beads and remove suspended solids from the top of the bed, the resin bed should be expanded at least 50% according to Fig 1.

In the case of non-conventional or upflow regenerated units, it may not be necessary to follow the above procedure.

Fig. 1 Bed Expansion vs. Backwash Flow Rate at various degrees Fahrenheit (F°)

Pressure Drop

Fig. 2 Pressure Drop vs Flow Rate at various degrees Fahrenheit (F°)

Operating Capacity

The following table (Fig 3.) shows the hydrogen cycle relationship between operating capacity and regeneration level when using sulfuric acid as the regenerant.

The calcium data is based on an acid concentration of 2% to avoid calcium sulfate precipitation. Higher operation capacities could be obtained using a step-wise increase in acid concentration to avoid the calcium problem. For more information please contact our technical department.

Fig. 3

Fig. 4

These suggestions and data are based on information we believe to be reliable. They are offered in good faith. However, we do not make any guarantee or warranty. We caution against using these products in an unsafe manner or in violation of any patents. Further, we assume no liability for the consequences of such actions.